Straight, honest reading on how RFID asset tracking actually works — where V-Tag active mesh tags fit, where passive UHF RFID fits, and how AssetWorx! runs both. Start with a guide, dig into the blog, or download a print-ready white paper.
Longer, plain-English walkthroughs of how RFID works and how to plan a system — the place to start if RFID is new to you.
The complete primer: how passive UHF and active V-Tag systems work, the frequencies and hardware involved, and where each approach fits best.
How to build a fast, reliable RFID checkout — choosing the right tags, plus the three station setups: mobile scanner, fixed reader, and fully automated.
Track assets indoors and out — pair active V-Tag mesh for zone-level indoor location with V-Tag GPS for wide-area outdoor coverage, no per-tag subscription.
How active V-Tag mesh gives hands-free, zone-level visibility across large floors and outdoor sites — with far less fixed infrastructure than a wired layout.
Everything on passive UHF — tags, labels and inlays, readers, antennas, and how choke-point capture reads assets by the hundred as they cross a boundary.
Focused articles on specific decisions — picking tags, weighing active against passive, and avoiding the traps that sink an RFID project.
A side-by-side look at cost, range, and infrastructure — and honest guidance on which one fits the job, or when to run both together.
Surface, size, and read range make or break reliability. How to match passive UHF tags to your assets — including the metal problem.
Where RFID pays off on the warehouse floor — and the honest trade-offs to weigh before you tag the first pallet.
The avoidable traps that sink RFID projects — unrealistic expectations, weak planning, the wrong tag choice, and untested readers.
Longer pieces on the decisions that actually decide whether a tracking project works — what the technology does, what it does not, and where the money goes.
Your CMMS flags affected units in seconds. Physically reaching every one of them is the real job, and the federal backstop behind you is thinner than most teams assume.
Zone-level presence and utilization, not a precision locator. What active RFID honestly does for pump hunts, equipment hoarding and audit trails.
What changed on January 1 2026, where medical equipment management moved to, and what an inventory has to be able to produce before your next survey.
Nearly every explainer says the TID cannot be copied. The chip makers now say otherwise. Why that matters for an asset audit that passes while the asset is gone.
It means at least three different things depending on who is saying it. Closing that gap before you price a system is how projects avoid disappointment.
Why a mesh of tags behaves differently from BLE beacons, and what that difference means for coverage, battery life and what you can actually promise.
Receiving docks, pack stations, aisle sweeps and shipping. Where passive UHF earns its place on the floor, and where it does not.
It is almost never the radio. The failures that end deployments are data, process and ownership problems wearing a technology costume.
Why two vendors can walk the same site and come back an order of magnitude apart, and how to read the difference instead of just picking the lower number.
The step teams skip and pay for later. Why the workflow has to be understood before a single reader is specified.
What is realistically knowable about a container and its contents in transit, and where tracking expectations outrun the technology.
Tracking material through heat, and why process monitoring and asset tracking answer different questions in the same plant.
Following a part from the mold onward, and the identity problem that shows up the moment two parts look identical.
Written from InfinID's own field experience — no jargon, no overclaims. Each is a clean, branded PDF you can share internally.
A side-by-side comparison of V-Tag active mesh tags and passive UHF RFID across cost, installation, location granularity and sensing — with honest guidance on when each is the right tool, and how AssetWorx! runs both together.
Get the white paper (PDF)How active mesh tags give continuous, hands-free, zone-level visibility of jobs, assemblies and tooling as they move across a plant floor — no chokepoints required — illustrated with an aircraft-engine MRO scenario.
Get the white paper (PDF)Tell us what you need to track — assets, work-in-process, tooling, personnel — and we'll point you to the right active or passive solution on AssetWorx!.
Request a quote